 | Buyers Push On Breather Cap - 1 1/2in. Dia.
Brand: Northern Tool Equipment
For 1 1/2in. outside diameter tube. U.S.A. | *$9.99 |
 | 1 1/2in. Gauge Mounting Flange
Brand: Northern Tool Equipment
Front flange for gauge mounting. | *$3.99 |
 | Breather Cap - 1/2in. NPT Size
Brand: Northern Tool Equipment
Ventilators filter particles as small as 40 microns. U.S.A. | *$6.99 |
| Breather Cap - 1in. NPT Size
Brand: Northern Tool Equipment
Ventilators filter particles as small as 40 microns. U.S.A. | *$9.99 |
 | Heavy-Duty Half Coupling - 1in. Size
Brand: Northern Tool Equipment
Use a flex coupling to direct-mount your engine to pump. Oil-resistant synthetic rubber inserts are used between the coupling halves to provide an equalized cushioned drive. When ordering, get one side to fit the motor and the other side to fit the pump shaft dia. Order two halves plus insert for complete coupling. When mounting, do not pound on the end of your pump shaft. U.S.A. Shaft Diameter (in.): LO99 HUB 1, Outside Diameter (in.): 2 1/2, Fits Models: LO99, L100, L110, Max. HP: 23, Max. RPM: 3,600, Material Type: Synthetic Rubber, Keyway (in.): 1/4 x 1/8 | *$19.99 |
 | Angle Type Mount
Brand: Northern Tool Equipment
For use with 11, 13.6 and 16 GPM two stage pumps and single stage Parker pumps. D-Series single stage | *$29.99 |
 | Hydraulic Pump Mounting Bracket
Brand: Northern Tool Equipment
With Northerns mounting brackets, you can speed assembly time, ensure shaft alignment and improve compactness and appearance at a reasonable price. 4-bolt brackets for J.S. Barnes 11, 13.6 and 16 GPM pumps. Items 3030 and 3031 are Zytel fiberglass-reinforced nylon, all others are cast aluminum. Fit our pumps 1012, 1053 and 1056. U.S.A. Bracket Length (in.): 4, Bolt Circle (in.): 3 5/8, Mounting Type: 4 bolt | *$29.99 |
 | Suction Strainer
Brand: Northern Tool Equipment
Suction strainer. Mounts through-the-wall of the reservoir using a 1-1/2in. NPT weld flange (not included). Suction port is 3/4in. NPT. 4in. long strainer has 100 mesh (149 micron) stainless steel screen. Fits our 2.8 and 4.8 gallon hydraulic tanks. Not for use with pumps over 10 GPM. | *$12.99 |
 | Heavy Duty Half Coupling - 1/2in. Size
Brand: Northern Tool Equipment
Use a flex coupling to direct-mount your engine to pump. Oil-resistant synthetic rubber inserts are used between the coupling halves to provide an equalized cushioned drive. When ordering, get one side to fit the motor and the other side to fit the pump shaft dia. Order two halves plus insert for complete coupling. When mounting, do not pound on the end of your pump shaft. U.S.A. Shaft Diameter (in.): LO99 HUB 1/2, Outside Diameter (in.): 2 1/2, Fits Models: LO99, L100, L110, Max. HP: 23, Max. RPM: 3,600, Keyway (in.): 1/8 x 1/16 | *$19.99 |
 | Buyers Hydraulic Tank --- 15 Gallon, Side-Mount, with Level/Temp Gauge, Model# SMR15S
Brand: Northern Tool Equipment
13 gauge HRPO steel with welded mounting angles. 1/4 turn chrome filler breather with basket strainer. Oil level gauge with temperature indicator. Interior baffle between suction and discharge. 2 in. NPT suction ports. 11 gallon usable capacity. U.S.A. Capacity (gal.): 15, Suction Port (in.): 2 NPT, Mount Type: Side, Material Type: 13 Gauge HRPO Steel, Dimensions L x W x H (in.): 13.5 x 15.5 x 17.5 | *$189.99 |
 | Standard Half Coupling - 5/8in. Size
Brand: Northern Tool Equipment
Use a flex coupling to direct-mount your engine to pump. Oil-resistant synthetic rubber inserts are used between the coupling halves to provide an equalized cushioned drive. When ordering, get one side to fit the motor and the other side to fit the pump shaft dia. Order two halves plus insert for complete coupling. When mounting, do not pound on the end of your pump shaft. U.S.A. Shaft Diameter (in.): LO95 HUB 5/8, Fits Models: LO90, LO95, Max. HP: 11.16, Max. Torque (in.-lbs.): 194, Max. RPM: 3,600, Material Type: Synthetic Rubber, Keyway (in.): 3/16 x 3/32 | *$13.99 |
 | Hydraulic Pump Mounting Bracket
Brand: Northern Tool Equipment
With Northerns mounting brackets, you can speed assembly time, ensure shaft alignment and improve compactness and appearance at a reasonable price. 2-bolt brackets for J.S. Barnes 22 and 28 GPM pumps. Fit our items 1057 and 1058 pumps. | *$64.99 |
| Hydraulic Pump Mounting Bracket
Brand: Northern Tool Equipment
With Northerns mounting brackets, you can speed assembly time, ensure shaft alignment and improve compactness and appearance at a reasonable price. 4-bolt brackets for J.S. Barnes 11, 13.6 and 16 GPM pumps. Items 3030 and 3031 are Zytel fiberglass-reinforced nylon, all others are cast aluminum. Fit our pumps 1012, 1053 and 1056. U.S.A. Bracket Length (in.): 5, Bolt Circle (in.): 3 5/8, Mounting Type: 4 bolt | *$29.99 |
 | Hydraulic Pump Mounting Bracket
Brand: Northern Tool Equipment
With Northerns mounting brackets, you can speed assembly time, ensure shaft alignment and improve compactness and appearance at a reasonable price. 4-bolt brackets for J.S. Barnes 11, 13.6 and 16 GPM pumps. Items 3030 and 3031 are Zytel fiberglass-reinforced nylon, all others are cast aluminum. Fit our pumps 1012, 1053 and 1056. U.S.A. Bracket Length (in.): 5 5/8, Bolt Circle (in.): 6 1/2, Mounting Type: 4 bolt | *$54.99 |
| Standard Half Coupling - 3/4in. Size
Brand: Northern Tool Equipment
Use a flex coupling to direct-mount your engine to pump. Oil-resistant synthetic rubber inserts are used between the coupling halves to provide an equalized cushioned drive. When ordering, get one side to fit the motor and the other side to fit the pump shaft dia. Order two halves plus insert for complete coupling. When mounting, do not pound on the end of your pump shaft. U.S.A. Shaft Diameter (in.): LO95 HUB 3/4, Outside Diameter (in.): 2 1/8, Fits Models: LO90, LO95, Max. HP: 11.16, Max. Torque (in.-lbs.): 194, Max. RPM: 3,600, Material Type: Synthetic Rubber, Keyway (in.): 3/16 x 3/32 | *$13.99 |
 | Breather Cap - 3in. Dia.
Brand: Northern Tool Equipment
Ventilators filter particles as small as 40 microns. U.S.A. | *$8.99 |
| 2 1/2in. Gauge Mounting Flange
Brand: Northern Tool Equipment
Front flange for gauge mounting. | *$3.99 |
 | Filter Strainer Breather Cap - 3in. Dia.
Brand: Northern Tool Equipment
Use this to fill hydraulic reservoirs. Allows up to 200 GPM or 26.7 CFM air flow. Keeps reservoir clean. Nickel-chrome plated cap. 5 1/4in. from top to bottom, cap is 3in. diameter. | *$12.99 |
 | Flow Meter
Brand: Northern Tool Equipment
Will handle up to 30 GPM at 5000 PSI. 4% FDS accuracy. Large 2 1/2in. direct read dial. Can be mounted horizontal or vertical. 3/4in. in and out ports. Comes with 1/4in. port to mount pressure gauge. Use on pressure or return line. Measures in GPM. | *$299.99 |
 | Insert For Heavy-Duty Half Coupling - 2 1/2in. Dia.
Brand: Northern Tool Equipment
L/AL099/100 Spider Sox. U.S.A. Outside Diameter (in.): 2 1/2, Material Type: Buna-N Rubber | *$12.99 |
| Heavy-Duty Half Coupling - 1 1/4in. Size
Brand: Northern Tool Equipment
Use a flex coupling to direct-mount your engine to pump. Oil-resistant synthetic rubber inserts are used between the coupling halves to provide an equalized cushioned drive. When ordering, get one side to fit the motor and the other side to fit the pump shaft dia. Order two halves plus insert for complete coupling. When mounting, do not pound on the end of your pump shaft. U.S.A. Shaft Diameter (in.): LO99 HUB 1 1/4, Fits Models: LO99, L100, L110, Max. HP: 23, Max. RPM: 3,600, Material Type: Synthetic Rubber, Keyway (in.): 1/4 x 1/8 | *$29.99 |
 | Metro Machine Check Valve, 3/4in. Port Size, 3000 PSI
Brand: Northern Tool Equipment
Will hold pressure in one direction and free flow in other. One end male pipe thread, other end female pipe thread. Free flow direction, male port to female port. Max pressure 3000 PSI. | *$22.99 |
 | Northman Fluid Power Hydraulic Directional Control Valve - 10.7 GPM, 4500 PSI, 3-Position, Double Solenoid, Tandem Center Spool, 12 Volt DC Solenoids, Model# SWH-G02-C3-D12-10
Brand: Northman Fluid Power
This industrial hydraulic directional control valve conforms to the National Fluid Power Association (NFPA) D03 mounting pattern for subplate or manifold mounting. As a four-way valve, it is commonly used to extend and retract a double-acting hydraulic cylinder or to control a rotary hydraulic motor. As a spring-centered valve, it will remain in its home position with P and T ports commonly connected until shifted electrically to one of two positions to either extend or retract a cylinder, returning to home when the power is removed. Its molded coils are moisture and dirt resistant. Indicating signal lights, manual override, bolt kit and electrical junction box are standard. The valve mounts on Northern Tool Subplate 203221 with 1/4in. NPT ports or 203231 with 3/8in. NPT Ports. | *$109.99 |
 | Northman Fluid Power Hydraulic Directional Control Valve - 16.8 GPM, 4500 PSI, 2-Position, Spring Offset, 120 Volt AC Solenoid, Model# SWH-G02-B2-A120-10
Brand: Northman Fluid Power
This industrial hydraulic directional control valve conforms to the National Fluid Power Association (NFPA) D03 mounting pattern for subplate or manifold mounting. As a four-way valve, it is commonly used to extend and retract a double-acting hydraulic cylinder. As a single-solenoid valve, it will remain in its home position until shifted electrically, returning to home when the power is removed. Its molded coils are moisture and dirt resistant. Indicating signal lights, manual override, bolt kit and electrical junction box are standard. The valve mounts on Northern Tool Subplate 203221 with 1/4in. NPT ports or 203231 with 3/8in. NPT Ports. | *$99.99 |
 | Northman Fluid Power Hydraulic Directional Control Valve - 19.8 GPM, 4500 PSI, 3-Position, Double Solenoid, Tandem Center Spool, 120 Volt AC Solenoids, Model# SWH-G03-C6-A120-10
Brand: Northman Fluid Power
This industrial hydraulic directional control valve conforms to the National Fluid Power Association (NFPA) D05 mounting pattern for subplate or manifold mounting. As a four-way valve, it is commonly used to extend and retract a double-acting hydraulic cylinder or to control a rotary hydraulic motor. As a spring-centered valve, it will remain in its home position with P and T ports commonly connected until shifted electrically to one of two positions to either extend or retract a cylinder, returning to home when the power is removed. Its molded coils are moisture and dirt resistant. Indicating signal lights, manual override, bolt kit and electrical junction box are standard. The valve mounts on Northern Tool Subplate 203321 with 3/8in. NPT ports or 203331 with 1/2in. NPT ports. | *$139.99 |
 | Northman Fluid Power Hydraulic Directional Control Valve - 25 GPM, 3000 PSI, Manual, 3/8in. NPT Ports, Model# HDT033C2
Brand: Northman Fluid Power
This Northman industrial 4-way valve is commonly used to extend and retract a double-acting hydraulic cylinder. It is actuated manually with the hand-lever. As a spring-centered valve, it will remain in its home all-ports blocked position until shifted to one of 2 positions to either extend or retract a cylinder, returning to home when the lever is released. | *$104.99 |
 | Northman Fluid Power Hydraulic Directional Control Valve - 26.4 GPM, 4500 PSI, 2-Position, Spring Offset, 120 Volt AC Solenoid, Model# SWH-G03-B2-A120-10
Brand: Northman Fluid Power
This industrial hydraulic directional control valve conforms to the National Fluid Power Association (NFPA) D05 mounting pattern for subplate or manifold mounting. As a four-way valve, it is commonly used to extend and retract a double-acting hydraulic cylinder. As a single-solenoid valve, it will remain in its home position until shifted electrically, returning to home when the power is removed. Its molded coils are moisture and dirt resistant. Indicating signal lights, manual override, bolt kit and electrical junction box are standard. The valve mounts on Northern Tool Subplates 203331 (3/8), 203341 (1/2) and 203361 (3/4). | *$124.99 |
| Northman Fluid Power Hydraulic Directional Control Valve - 26.4 GPM, 4500 PSI, 3-Position, Double Solenoid, Closed Center Spool, 120 Volt AC Solenoids, Model# SWH-G03-C2-A120-10
Brand: Northman Fluid Power
This industrial hydraulic directional control valve conforms to the National Fluid Power Association (NFPA) D05 mounting pattern for subplate or manifold mounting. As a four-way valve, it is commonly used to extend and retract a double-acting hydraulic cylinder or to control a rotary hydraulic motor. As a spring-centered valve, it will remain in its home all-ports blocked position until shifted electrically to one of two positions to either extend or retract a cylinder, returning to home when the power is removed. Its molded coils are moisture and dirt resistant. Indicating signal lights, manual override, bolt kit and electrical junction box are standard. The valve mounts on Northern Tool Subplate 203321 with 3/8in. NPT ports or 203331 with 1/2in. NPT ports. | *$139.99 |
| Northman Fluid Power Hydraulic Directional Control Valve - 26.4 GPM, 4500 PSI, 3-Position, Double Solenoid, Open Center Spool, 120 Volt AC Solenoids, Model# SWH-G03-C3-A120-10
Brand: Northman Fluid Power
This industrial hydraulic directional control valve conforms to the National Fluid Power Association (NFPA) D05 mounting pattern for subplate or manifold mounting. As a four-way valve, it is commonly used to extend and retract a double-acting hydraulic cylinder or to control a rotary hydraulic motor. As a spring-centered valve, it will remain in its home position with all-ports commonly connected until shifted electrically to one of two positions to either extend or retract a cylinder, returning to home when the power is removed. Its molded coils are moisture and dirt resistant. Indicating signal lights, manual override, bolt kit and electrical junction box are standard. The valve mounts on Northern Tool Subplate 203321 with 3/8in. NPT ports or 203331 with 1/2in. NPT ports. | *$139.99 |
 | Northman Fluid Power In-Line Hydraulic Check Valve - 17.1 GPM, 3000 PSI, 1/2in. NPT Ports, Model# CIT0405
Brand: Northman Fluid Power
This Northman in-line check valve is designed to allow free flow of oil in a hydraulic system in one direction and block flow in the reverse direction. | *$24.99 |
 | Northman Fluid Power In-Line Hydraulic Check Valve - 30.4 GPM, 3000 PSI, 3/4in. NPT Ports, Model# CIT0605
Brand: Northman Fluid Power
This Northman in-line check valve is designed to allow free flow of oil in a hydraulic system in one direction and block flow in the reverse direction. | *$29.99 |
 | Northman Fluid Power In-Line Hydraulic Flow Control Valve - 8 GPM, 3000 PSI, 3/8in. NPT Ports, Model# TVT03
Brand: Northman Fluid Power
This Northman in-line adjustable flow control needle valve is designed to restrict the flow of oil in a hydraulic system to control the speed of a cylinder or motor. | *$36.99 |
 | Northman Fluid Power In-Line Hydraulic Flow Control Valve with Reverse Free Flow - 8 GPM, 3000 PSI, 3/8in. NPT Ports, Model# TCVT03
Brand: Northman Fluid Power
This Northman in-line adjustable flow control valve is designed to restrict the flow of oil in a hydraulic system to control the speed of a cylinder or motor. The flow in one direction is metered as adjusted. The flow in the opposite direction is full free flow over a check valve. | *$44.99 |
 | Northman Fluid Power In-Line Hydraulic Needle Valve - 20 GPM, 3000 PSI, 3/4in. NPT Ports, Model# TVT06
Brand: Northman Fluid Power
This Northman in-line adjustable needle valve is designed to restrict the flow of oil in a hydraulic system in order to control the speed of a cylinder or motor. | *$64.99 |
 | Northman Fluid Power In-Line Hydraulic Relief Valve - 50 GPM, 100-1000 PSI Adjustable, 3550 PSI, 3/4in. NPT Ports, Model# RFT061
Brand: Northman Fluid Power
This Northman adjustable relief valve is designed to limit the operating pressure in a hydraulic system to a maximum set pressure. The valve may be connected into the pressure line so that system pressure flows through, or it may be teed off the pressure line with one of the pressure ports plugged. When the system reaches the maximum desired setting, the internal piston moves to smoothly relieve pressure to tank, maintaining stable pressure control and repeatability. Ports are also provided for a gauge and for remote pressure control. | *$89.99 |
 | Northman Fluid Power In-Line Hydraulic Relief Valve - 50 GPM, 1000-3550 PSI Adjustable, 3550 PSI, 3/4in. NPT Ports, Model# RFT063
Brand: Northman Fluid Power
This Northman adjustable relief valve is designed to limit the operating pressure in a hydraulic system to a maximum set pressure. The valve may be connected into the pressure line so that system pressure flows through, or it may be teed off the pressure line with one of the pressure ports plugged. When the system reaches the maximum desired setting, the internal piston moves to smoothly relieve pressure to tank, maintaining stable pressure control and repeatability. Ports are also provided for a gauge and for remote pressure control. | *$89.99 |
 | Northman Fluid Power In-Line Hydraulic Relief Valve - 50 GPM, 500-2000 PSI Adjustable, 3550 PSI, 3/4in. NPT Ports, Model# RFT062
Brand: Northman Fluid Power
This Northman adjustable relief valve is designed to limit the operating pressure in a hydraulic system to a maximum set pressure. The valve may be connected into the pressure line so that system pressure flows through, or it may be teed off the pressure line with one of the pressure ports plugged. When the system reaches the maximum desired setting, the internal piston moves to smoothly relieve pressure to tank, maintaining stable pressure control and repeatability. Ports are also provided for a gauge and for remote pressure control. | *$89.99 |
 | Northman Fluid Power Modular Hydraulic Flow Control Valve - 20 GPM, 3000 PSI, Ports A B, Reverse Free Flow, Model# MT03
Brand: Northman Fluid Power
This Northman flow control valve is designed to restrict the flow of oil in a hydraulic system to control the speed of a cylinder or motor. The flow in one direction is metered as adjusted. The flow in the opposite direction is a free flow over a check valve. Valve mounts as a modular unit between a D05 size directional control valve and the subplate. Contains 2 separate pilot-operated check valves-one each on A cylinder port and B cylinder port. Allows metered flow adjustment in the cylinder ports as the flow exits, controlling the speed of the cylinder. As separate valves, speed may be controlled independently for the extend and retract operations. Requires longer than standard bolt kit to mount this flow control in valve stack. | *$109.99 |
 | Northman Fluid Power Modular Hydraulic Flow Control Valve - 9.3 GPM, 3000 PSI, Ports A B, Reverse Free Flow, Model# MT02
Brand: Northman Fluid Power
This Northman flow control valve is designed to restrict the flow of oil in a hydraulic system to control the speed of a cylinder or motor. The flow in one direction is metered as adjusted. The flow in the opposite direction is a free flow over a check valve. Valve mounts as a modular unit between a D03 size directional control valve and the subplate. Contains 2 separate pilot-operated check valves-one each on A cylinder port and B cylinder port. Allows metered flow adjustment in the cylinder ports as the flow exits, controlling the speed of the cylinder. As separate valves, speed may be controlled independently for the extend and retract operations. Requires longer than standard bolt kit to mount this flow control in valve stack. | *$79.99 |
 | Northman Fluid Power Modular Pilot-Operated Check Valve - 20 GPM, 3000 PSI, Ports A B, Model# MPC03
Brand: Northman Fluid Power
Northman pilot-operated check valve is designed to block the flow of oil in a hydraulic system to hold the position of a cylinder when the directional control valve is shifted to the neutral center position. Flow is restored by a pilot pressure signal releasing the check valve when the directional control valve is extending or retracting the cylinder. Valve mounts as a modular unit between a D03 size directional control valve and the subplate. Contains 2 separate pilot-operated check valves-one each on A cylinder port and B cylinder port. Requires longer than standard bolt kit to mount this flow control in valve stack. | *$109.99 |
 | Northman Fluid Power Modular Pilot-Operated Check Valve - 9.3 GPM, 3000 PSI, Ports A B, Model# MPC02
Brand: Northman Fluid Power
Northman pilot-operated check valve is designed to block the flow of oil in a hydraulic system to hold the position of a cylinder when the directional control valve is shifted to the neutral center position. Flow is restored by a pilot pressure signal releasing the check valve when the directional control valve is extending or retracting the cylinder. Valve mounts as a modular unit between a D03 size directional control valve and the subplate. Contains 2 separate pilot-operated check valves-one each on A cylinder port and B cylinder port. Requires longer than standard bolt kit to mount this flow control in valve stack. | *$79.99 |
 | Northman Fluid Power Modular Valve Stack Bolt Kit - To Mount 1 NFPA D03 Valve 1 NFPA D03 Modular Valve, Model# MBK021
Brand: Northman Fluid Power
This Northman bolt kit includes 4 threaded bolts and 4 nuts to mount a stack of one directional control valve and one modular valve. Designed for the NFPA D03 size valve series. | *$19.99 |
 | Northman Fluid Power Modular Valve Stack Bolt Kit - To Mount One NFPA D03 Valve 2 NFPA D03 Modular Valves, Model# MBK022
Brand: Northman Fluid Power
This Northman bolt kit includes 4 threaded bolts and 4 nuts to mount a stack of one directional control valve and two modular valves. Designed for the NFPA D03 size valve series. | *$21.99 |
 | Northman Fluid Power Modular Valve Stack Bolt Kit - To Mount One NFPA D05 Valve 1 NFPA D05 Modular Valve, Model# MBK031
Brand: Northman Fluid Power
This Northman bolt kit includes 4 threaded bolts and 4 nuts to mount a stack of one directional control valve and one modular valve. Designed for the NFPA D05 size valve series. | *$21.99 |
 | Northman Fluid Power Modular Valve Stack Bolt Kit - To Mount One NFPA D05 Valve 2 NFPA D05 Modular Valves, Model# MBK032
Brand: Northman Fluid Power
This Northman bolt kit includes 4 threaded bolts and 4 nuts to mount a stack of one directional control valve and two modular valves. Designed for the NFPA D05 size valve series. | *$24.99 |
 | Northman Single-Station Subplate - NFPA D03 Pattern, 3/8in. NPT Side Ports, Model# M02-03-S-2
Brand: Northman Fluid Power
This single-station subplate for mounting an industrial hydraulic directional control valve conforms to the National Fluid Power Association (NFPA) D03 mounting pattern. It accepts Northern Tool valves in the 20130* and 20230* Series. The 3/8in. NPT female ports are side mounted for the Pressure, Tank, A and B ports. | *$49.99 |
 | Northman Single-Station Subplate - NFPA D05 Pattern, 3/4in. NPT Side Ports, Model# M03-06-S-2
Brand: Northman Fluid Power
This single-station subplate for mounting an industrial hydraulic directional control valve conforms to the National Fluid Power Association (NFPA) D05 mounting pattern. It accepts Northern Tool valves in the 20150* and 20250* Series. The 3/4in. NPT female ports are side mounted for the Pressure, Tank, A and B ports. | *$54.99 |
| Northman Fluid Power Hydraulic Directional Control Valve - 16.8 GPM, 4500 PSI, 3-Position, Double Solenoid, Closed Center spool, 120 Volt AC Solenoid, Model# SWH-G02-C2-A120-10
Brand: Northman Fluid Power
This industrial hydraulic directional control valve conforms to the National Fluid Power Association (NFPA) D03 mounting pattern for subplate or manifold mounting. As a four-way valve, it is commonly used to extend and retract a double-acting hydraulic cylinder or to control a rotary hydraulic motor. As a spring-centered valve, it will remain in its home all-ports blocked position until shifted electrically to one of two positions to either extend or retract a cylinder, returning to home when the power is removed. Its molded coils are moisture and dirt resistant. Indicating signal lights, manual override, bolt kit and electrical junction box are standard. The valve mounts on Northern Tool Subplate 203221 with 1/4in. NPT ports or 203231 with 3/8in. NPT Ports | *$109.99 |
| Northman Fluid Power Hydraulic Directional Control Valve - 16.8 GPM, 4500 PSI, 3-Position, Double Solenoid, Closed Center Spool, 12 Volt DC Solenoids, Model# SWH-G02-C2-D12-10
Brand: Northman Fluid Power
This industrial hydraulic directional control valve conforms to the National Fluid Power Association (NFPA) D03 mounting pattern for subplate or manifold mounting. As a four-way valve, it is commonly used to extend and retract a double-acting hydraulic cylinder or to control a rotary hydraulic motor. As a spring-centered valve, it will remain in its home all-ports blocked position until shifted electrically to one of two positions to either extend or retract a cylinder, returning to home when the power is removed. Its molded coils are moisture and dirt resistant. Indicating signal lights, manual override, bolt kit and electrical junction box are standard. The valve mounts on Northern Tool Subplate 203221 with 1/4in. NPT ports or 203231 with 3/8in. NPT ports. | *$109.99 |
 | Northman Single-Station Subplate - NFPA D05 Pattern, 1/2in. NPT Side Ports, Model# M03-04-S-2
Brand: Northman Fluid Power
This single-station subplate for mounting an industrial hydraulic directional control valve conforms to the National Fluid Power Association (NFPA) D05 mounting pattern. It accepts Northern Tool valves in the 20150* and 20250* Series. The 1/2in. NPT female ports are side mounted for the Pressure, Tank, A and B ports. | *$49.99 |
|
