 | Brave Grapple for 3-Pt. Tractor Hitch, Model# SB-O3
Brand: Brave
Use with tractors in 20-60 HP range. Fits category 1, 2, and 3 tractor hitches. Lifts up to 2000 lbs. Opens to 55in. (inside) and handles logs up to 3-ft. dia. Grapple locks at 90deg for side loading. U.S.A. Hitch Type: 3-Point, Category Type: 1, 2, 3, Required HP: 20 - 60, Capacity (lbs.): 2,000 | *$2,999.99 |
 | Brave Grapple for Skid Steer Loader, Model# SL-O3
Brand: Brave
Use with loaders in 30-60 HP range. Lifts up to 2000 lbs. Opens to 55in. (inside) and handles logs up to 3-ft. dia. Grapple locks at 90deg for side loading. Universal mounting plate to fit all skid steer loaders. Pivots up to 135#176; in either direction. U.S.A. | *$3,299.99 |
 | Brune Farm Inc. POST Steel Post Driver
Brand: Brune Farm Inc. Part Number: POST
A 1 man proposition. 1 man may drive between 200 to 300 posts a day without strain. No holes to dig. Weighted driver is placed over head of post and worked up and down like a pile driver. Inside diameter 2 1 2". 17 lb. | *$29.99 |
 | Buffalo Tools Pro-Series 4.0-Cu. Ft. Cement Mixer
Brand: Buffalo Part Number: 52932362
Mix cement at the construction site with this 2/3 hp, 110V motorized cement mixer. Its drum tips 360° to make pouring cement in the right place easy, and the 15" diameter opening enables fast pouring.bProduct Features:/bulDouble insulated15" diameter drum opening for fast pouringDrum tips 360° for easy cement placement180-lb. dry mix capacity2/3 hp, 110V motor/ul(Model CME35) | *$399.99 |
 | Electric Fencer "Cow Trainer" - ELECTRIC FENCER "COW TRAINER"
Brand: Bulldozer Part Number: 8200
Electric Fencer "Cow Trainer" - *Designed for dairy barns. *3 Position switch: High-3,000 volts, Low-1,500 volts,Off *UL listed* Digital technology | *$64.00 |
 | Columbus McKinnon M1196E E-Grip Hitch Pin
Brand: C M Chain Model: M1196E Part Number: M1196E
Ergonomic design. Highest strength. Micro allow steel. Hot forged. Thru hardened heat treatment for strength properties. Supplied with hitch pin. Wide ergonomic handle. Big Orange. No. M1196E: 1 2" pin diameter, 3 1 2" useable length No. M1201E: 5 8" pin | *$4.55 |
 | Wire Stretcher - 12369 88 250Lb Wire Stretcher
Brand: C M Chain Model: 12369 Part Number: 12369
Four heavy steel sheaves, double swivel. No. 12368 - Equipped with 16 feet of 3/8'' sisal rope and 30'' of chain. Also equipped with a positive action locking device. Can be used for light-duty hoisting. Wire grips No.23 chain, No.25 upper block. Workingload limit 250 lbs. No.12369 - Equipped with four pulleys, roller bearings and swivels. Two pulleys included in each block. Furnished with 24 feet of 1/2'' polypropylene rope and 30'' of chain for anchoring to post. Can be used as a rope hoist. Also equipped with a positive action locking device, to maintain tension. Can be used as a light-duty hoist. Wire grips No.88 upper block. Working load limit 450 lbs. | *$83.63 |
 | C.R. LAURENCE 0377005 CRL Panther Edger Replacement Spindle Bearing
Brand: C.R. Laurence Part Number: 0377005
Designed for CRL's Panther Edger This high quality CRL Panther Edger Replacement Spindle Bearing is used on the CRL Panther Edger to support the main spindle when in operation. Replacement can be accomplished by a qualified mechanic. Bearings are normally replaced as a set but are sold individually. | *$47.46 |
 | C.R. LAURENCE 0377006 CRL Panther Edger Front Oil Seal
Brand: C.R. Laurence Part Number: 0377006
Designed for CRL's Panther Edger This CRL Panther Edger Front Oil Seal is used with the CRL Panther Glass Edger. It keeps out contaminants such as dirt and water from the spindle shaft. Replacing this seal should be done by a qualified person who has previous experience with repairing machinery. Minimum Order: 1 Each | *$19.48 |
 | C.R. LAURENCE 0377007 CRL Panther Edger V-Ring Shaft Seal
Brand: C.R. Laurence Part Number: 0377007
Designed for CRL's Panther Edger This CRL Panther Edger V-Ring Shaft Seal is used with the Panther Glass Edger. It keeps the shaft and bearing lubricants in and contaminants such as dirt and water out. Replacing this seal should be done by a qualified person who has previous experience with repairing machinery. Minimum Order: 1 Each | *$33.88 |
 | C.R. LAURENCE 0377008 CRL Panther Edger Shaft for Spindle
Brand: C.R. Laurence Part Number: 0377008
Designed for CRL's Panther Edger This CRL Shaft for Panther Edger Spindle is used with the Panther Glass Edger. Replacing this item should be done by a qualified person who has previous experience with repairing machinery. Minimum Order: 1 Each | *$245.57 |
 | C.R. LAURENCE 0377010 CRL Panther Edger Motor Assembly
Brand: C.R. Laurence Part Number: 0377010
Designed for CRL's Panther Edger This motor is the workhorse of the CRL Panther Edging Machine. This one horsepower, single phase motor lasts almost indefinitely. Stocked and shipped out of Los Angeles only. Minimum Order: 1 Each | *$703.01 |
 | C.R. LAURENCE 0377028 CRL Panther Edger Replacement Drive Belt
Brand: C.R. Laurence Part Number: 0377028
Designed for CRL Panther Edger This CRL Replacement Drive Belt is used on all original belt driven Panther Glass Edger's. Over time these belts stretch and wear, and need replacing. Should be replaced during a major machine overhaul. Its two inch (51 millimeter) width is standard. Minimum Order: 1 Each | *$147.30 |
 | C.R. LAURENCE 0377031 CRL Panther Edger Replacement Ribbed Roller Bearing Bushing
Brand: C.R. Laurence Part Number: 0377031
Designed for CRL's Panther Edger Made for the CRL Panther Edger , this replacement CRL Ribbed Roller Bearing Bushing comes ready to install to help ensure smooth edger operation. Replacement invoves removing the old bearing with a press. | *$20.49 |
 | C.R. LAURENCE 0377032 CRL Panther Edger Idler Gear
Brand: C.R. Laurence Part Number: 0377032
Designed for use with CRL's Panther Edger This CRL Idler Gear is used for guiding the drive belt and to make it track correctly, by keeping the proper tension. Gear is made from rolled steel and rides on a bearing. Used on the CRL Panther Edger . | *$178.06 |
 | C.R. LAURENCE 0377034 CRL Panther Edger Brass Nut
Brand: C.R. Laurence Part Number: 0377034
Designed for CRL's Panther Edger This heavy CRL Brass Nut secures the diamond wheel and polishing wheel to the Panther Glass Edger . The solid brass material resists corrosion, preventing it from becoming "frozen" onto the spindle shaft. Always use the correct wrench to tighten to avoid stripping. | *$66.60 |
 | C.R. LAURENCE 0377036 CRL Panther Edger Height Adjustment Handle
Brand: C.R. Laurence Part Number: 0377036
Designed for CRL's Panther Edger This CRL Height Adjustment Handle raises and lowers the diamond wheel on the CRL Panther Edger . The black plastic knob with brass shaft easily attaches to the height adjustment linkage. | *$55.70 |
 | C.R. LAURENCE 0377111 CRL Panther Edger 110 Volt Coolant Pump
Brand: C.R. Laurence Part Number: 0377111
Designed for CRL's Panther Edger This high quality pump was designed for use with the CRL Panther Edger . It delivers Coolant to the Grinding Wheel and at the same time it lubricates the surrounding machine parts. The pump sits in the tank and usually works best if it is suspended from the bottom, as it will not be as prone to contaminants. Periodic cleaning of the sediment screen will prolong the life of the pump. | *$146.13 |
| | C.R. LAURENCE 0377729 CRL Panther Edger Back Support Roller Bar
Brand: C.R. Laurence Part Number: 0377729
Used Exclusively on the CRL Panther Edger The CRL Panther Edger Back Support Roller Bar can be used as an additional support for your CRL Panther Edger or can be used in conjunction with the CRL Panther Height Extension Kit . Wheels are adjustable for spacing and removable if necessary. | *$61.54 |
 | C.R. LAURENCE 1100KR CRL Upright Belt Sander Upper Pulley Bearings
Brand: C.R. Laurence Part Number: 1100KR
Fits Series 200 2000 Belt Machines This CRL Upper Pulley Bearing is inserted into the pulley, which is then placed on a one inch (25 millimeter) shaft. | *$133.40 |
 | C.R. LAURENCE 16100060 CRL/Somaca Toggle Clamp for BM106G Machine
Brand: C.R. Laurence Part Number: 16100060
Replacement Part for BM106G Wet Abrasive Upright Sander This part is for all (1987 to present) BM106G Wet Abrasive Belt Machines. Item Number on Schematic: 17B Quantity Required Per Machine: 1 | *$21.76 |
 | C.R. LAURENCE 2000175 CRL Lower Pulley for the 200 and 2000 Sander - 7/8 Arbor
Brand: C.R. Laurence Part Number: 2000175
Used On Early Model 2000 Sanders Using a Westinghouse Motor This cast iron CRL Lower Pulley has a 7/8 inch (22.2 millimeter) arbor. Used on all early model 2000 Series Sanders using a Westinghouse motor. | *$214.03 |
 | C.R. LAURENCE 20040 CRL Upper Pulley for the 200 and 2000 Sander
Brand: C.R. Laurence Part Number: 20040
Fits All 200 2000 Belt Machines This cast iron CRL Upper Pulley is to be used in conjunction with two 1100KR bearings on the 200 and 2000 Series Sanders. | *$154.10 |
 | C.R. LAURENCE 2200 CRL 4 X 106 Wet Abrasive Belt Sander Without Roller Platen
Brand: C.R. Laurence Part Number: 2200
New Fiberglass Tank Won't Rust Rugged Construction and a One H.P. Direct-Drive Motor Also Available for Australia with 240 v. 50 Hz. Power Streamlined styling, rugged construction and the affordable price makes our CRL Upright Wet Belt Sander without Platen ideal for use by glass fabricators and processors. The CRL Wet Belt Sander is designed to use the most popular size four by 106 inches (101.6 by 2692.4 millimeters) wet or dry abrasive belts to sand edges to the desired finish. Features of the 2200 Sanding Machine include Direct drive, one H.P., 60 cycle, 110 Volt AC Motor Five Inch (127 millimeter) Diameter Drive Pulley Motor can be wired for 220 Volts at an additional cost. Our New CRL 2200SS Belt Guard Safety Shield helps protect the operator in the event of accidental belt breakage. To solve the problem of water tank spray corrosion, we've replaced the steel tank with a Non-Rusting Fiberglass Water Tank. Securely fastened with six mounting bolts, the tank is trimmed with rugged U-Channel. When you consider all of these features, it's easy to see why glass shops large and small have made the 2200 the glass industry's most popular Upright Belt Sander. For more information, or machine specifications, contact us at (888) 663-9830, or email us here . BELT SELECTION: CRL Wet Abrasive Belts in the four by 106 inch size are recommended for the 2200. The most popular are the: CRL4X106120X 120X Grit Smooth Finish, and Cat. No. CRL4X10680X 80X Grit Rough Finish, but other grits from 36X (Super Coarse) to 600X (Super Fine) are available for this machine, along with Cork Belts for high polishing. | *$2,747.92 |
 | C.R. LAURENCE 2200110VMTR CRL 1 Horsepower 110 Volt Motor for the 2200 Series Sanders
Brand: C.R. Laurence Part Number: 2200110VMTR
Used On All 2200 Upright Belt Sanders This CRL One H.P. Motor is used on all 2200 Series Upright and 100BM Bench Model sanders. Has a one inch shaft for a lower pulley. | *$903.24 |
 | C.R. LAURENCE 2200720 CRL Single Spray Nozzle for 2200RP
Brand: C.R. Laurence Part Number: 2200720
Used on All 2200 Series Belt Sanders This CRL Water Spray Nozzle is used on all model 2200 and 2200RP wet belt sanders. Sprays belt with water to cut faster and cooler, reduce belt wear and eliminate sanding dust. Spray nozzle is also used on model 100BM belt sander. | *$18.61 |
 | C.R. LAURENCE 2200725 CRL Electric Water Valve
Brand: C.R. Laurence Part Number: 2200725
Used on All 2200 Series Belt Sanders CRL Electric Water Valve and Spray Nozzle is used on all 2200 and 2200RP sanders. Sprays belt with water to cut faster and cooler, reduce belt wear and eliminate sanding dust. This Water Valve is also used on CRL's 100BM sander. | *$124.70 |
 | C.R. LAURENCE 2200735 CRL Replacement Bearings for Older Upper Pulleys
Brand: C.R. Laurence Part Number: 2200735
Used on Older Model 2200 Sanders Manufactured Before 1987 This CRL Replacement Bearing is used on older model sanders manufactured before June 1987 and fit the 2200750 shaft. Top quality materials are guaranteed to give you years of service. | *$246.55 |
 | C.R. LAURENCE 2200745 CRL Two Piece Steel Upper/Lower Pulley
Brand: C.R. Laurence Part Number: 2200745
Used on CRL Upright Belt Sanders This CRL Upper and Lower Pulley is for the 2200 Series and 100BM Sanders. It replaces the lower pulley on all models, and replaces the upper pulley on all models in serial number series: 1071-1347 to 1071-1393; 1071-1421 to 1071-1493 and 1001 to current models. The two-piece steel pulley can be removed without a pulley removal tool. Description: 2 Piece Upper/Lower Pulley | *$258.75 |
 | C.R. LAURENCE 2200750 CRL Replacement Pulley Shaft With C-Rings for 2200 Series Sanders
Brand: C.R. Laurence Part Number: 2200750
Used on Older Model Sanders This shaft is for older 2200 and 2200RP Sanders manufactured until June 1987. The 2200750 Shaft has a slightly smaller diameter on one half of the shaft. The appropriate bearings for this shaft are the 2200735 . | *$140.89 |
 | C.R. LAURENCE 2200760 CRL Rest Roller Bolt and Nut
Brand: C.R. Laurence Part Number: 2200760
Used on All 2200RP Belt Sanders CRL Rest Rollers and Bolts fit the front roller guide bar on all 2200RP sanders. Rollers are shipped with bolt sleeves. Bolts are supplied with a retaining nut and lock washer. | *$10.35 |
 | C.R. LAURENCE 2200765 CRL Front Rest Roller and Sleeve for the 2200RP Sander
Brand: C.R. Laurence Part Number: 2200765
Used on All 2200RP Belt Sanders This CRL Front Rest Roller and Sleeve fits the front roller guide bar on all 2200RP sanders. Rollers are shipped with bolt sleeves, the bolt, nut and washer is sold separately. Diameter: 3 in (76 mm) Width: 1-1/4 in (32 mm) Axle: 3/8 in (9.5 mm) | *$24.27 |
 | C.R. LAURENCE 2200780 CRL Belt Tightening Device Backstand Idler and Pulley
Brand: C.R. Laurence Part Number: 2200780
Used on Late Model Sanders This CRL Belt Tightening Device is used on late model sanders with serial numbers in these series: 1071-1347 to 1071-1393, 1071-1421 to 1071-1493 and 1001 to current models. Image shows Backstand Idler and Pulley. | *$1,236.98 |
 | C.R. LAURENCE 2200785 CRL Belt Tightening Device Backstand Idler and Shaft
Brand: C.R. Laurence Part Number: 2200785
Used on Late Model Sanders This is the Same As 2200780 But Without the Pulley This CRL Belt Tightening Device is used on late model sanders with serial numbers in these series: 1071-1347 to 1071-1393, 1071-1421 to 1071-1493 and 1001 to current models. Image shows Backstand Idler and Pulley. | *$1,118.01 |
 | C.R. LAURENCE 2200795 CRL Replacement Bearing for the CRP2000
Brand: C.R. Laurence Part Number: 2200795
Fits All 2200 Series and 100BM Belt Sanders Manufactured After 1987. CRL Roller Platen Replacement Bearings are for the 2200 , 2200RP and the 100BM belt sanders. Replacing the bearings help to reduce belt wear by minimizing friction between the belt and platen. | *$128.31 |
 | C.R. LAURENCE 2200RP CRL 4 X 106 Wet Abrasive Belt Sander With Roller Platen
Brand: C.R. Laurence Part Number: 2200RP
Rugged Construction and 1 H.P. Direct-Drive Motor Makes This Our Most Popular Belt Machine Ever Complete with Roller Platen, Front Rest Guide Roller Bar, Belt Guard Safety Shield and Rust-Resistant Fiberglass Water Tank Also Available in a 220 V. 50 Hz. Model for Australia, Cat. No. AU22 Streamlined styling, rugged construction and the affordable price makes our CRL Upright Wet Belt Sander ideal for use by glass fabricators and processors. The CRL Wet Belt Sander is designed to use popular size four inch by 106 inches (101.6 X 2692.4 millimeters) wet or dry abrasive belts to sand edges to the desired finish. Features of the 2200RP Sanding Machine include Direct Drive, One H.P., 60 cycle, 110 Volt AC Motor Five Inch (127 millimeter) Diameter Drive Pulley Fast Belt Changing Mechanism Durable Urethane Covered Roller Platen Front Rest Roller Guide Bar. Belt guard Safety Shield. Electric Water Valve. Non-Rusting Fiberglass Water Tank Motor can be wired for 220 Volts at an additional cost. Our New CRL 2200SS Belt Guard Safety Shield helps protect the operator in the event of accidental belt breakage. To solve the problem of water tank spray corrosion, we've replaced the steel tank with a Non-Rusting Fiberglass Water Tank. Securely fastened with six mounting bolts, the tank is trimmed with rugged U-Channel. When you consider all of these features, it's easy to see why glass shops large and small have made the 2200RP the glass industry's most popular Upright Belt Sander. For more information, or machine specifications, contact us at (888) 663-9830, or email to us at . BELT SELECTION: CRL Wet Abrasive Belts in the four by 106 inch size are recommended for the 2200RP. The most popular are belts are: CRL4X106120X 120X Grit Smooth Finish, and Cat. No. CRL4X10680X 80X Grit Rough Finish, but other grits from 36X (Super Coarse) to 600X (Super Fine) are available for this machine, along with Cork Belts for high polishing. | *$2,700.46 |
| C.R. LAURENCE 2200RP220V CRL 4 X 106 Wet Abrasive 220 Volt Belt Sander With Roller Platen
Brand: C.R. Laurence Part Number: 2200RP220V
Factory Wired to 220 Volts and Rugged Construction 1 H.P. Direct-Drive Motor Makes This Our Most Popular Belt Machine Ever Complete with Roller Platen, Front Rest Guide Roller Bar, Belt Guard Safety Shield and Rust-Resistant Fiberglass Water Tank Also Available in a 220 V. 50 Hz. Model for Australia, Cat. No. AU22 Streamlined styling, rugged construction and the affordable price makes our CRL Upright Wet Belt Sander ideal for use by glass fabricators and processors. The CRL Wet Belt Sander is designed to use popular size four inch by 106 inch (101.6 X 2,692.4 millimeter) wet or dry abrasive belts to sand edges to the desired finish. Features of the 2200RP include Direct Drive, 1 H.P., 60 cycle, 220 Volt AC Motor Five Inch (127 millimeter) Diameter Drive Pulley Urethane Covered Roller Platen Front Rest Roller Guide Bar. Our New CRL 2200SS Belt Guard Safety Shield helps protect the operator in the event of accidental belt breakage. To solve the problem of water tank spray corrosion, we've replaced the steel tank with a Non-Rusting Fiberglass Water Tank. Securely fastened with six mounting bolts, the tank is trimmed with rugged U-Channel. When you consider all of these features, it's easy to see why glass shops large and small have made the 2200RP the glass industry's most popular Upright Belt Sander. For more information, or machine specifications, contact us at (888) 663-9830, or email to us at . BELT SELECTION: CRL Wet Abrasive Belts in the 4 X 106 inch size are recommended for the 2200RP. The most popular are Cat. No. CRL4X106120X 120X Grit Smooth Finish, and Cat. No. CRL4X10680X 80X Grit Rough Finish, but other grits from 36X (Super Coarse) to 600X (Super Fine) are available for this machine, along with Cork Belts for high polishing. Note: ALL 2200RP220V MACHINES MUST SHIP FROM THE MANUFACTURER IN TEXAS TO THE CUSTOMER'S NEAREST CRL BRANCH - NOT DIRECT FROM THE MANUFACTURER. CUSTOMERS ARE RESPONSIBLE FOR FREIGHT FROM | *$2,812.91 |
 | C.R. LAURENCE 2200SS CRL Belt Guard Safety Shield for the 2200, 2200RP and AU22 Upright Belt Sander
Brand: C.R. Laurence Part Number: 2200SS
Gives Added Protection for the Operator O.S.H.A. Recommended Easy Bolt-On Installation to Your Existing 2200RP, 2200 or AU22 Upright Wet Belt Sander The CRL Belt Guard Safety Shield for the 2200, 200RP and AU22 Upright Belt Sander protects your face and eyes from flying debris, giving you an added degree of safety. The 2200SS is standard equipment on the new CRL 2200 , CRL 2200RP and CRL AU22 Sanders. It can also be retro-fitted on older 2200, 2200RP and AU22 Model Sanders. For safety, this is an attachment no shop should be without. This new addition to our line of sanders offers the piece of mind you need when working with power tools such as the 2200, 2200RP and AU22 Upright Sanders. One each per package. Follow all safety precautions when operating machinery. Failure to do so can result in injury. Height: 18 in (457.2 mm) Width: 6 in (152.4 mm) | *$154.34 |
 | C.R. LAURENCE 2402500 CRL/Somaca 6 x 8 Counterbalanced Tilting Cutting Table
Brand: C.R. Laurence Part Number: 2402500
Indoor/Outdoor Carpet: Cushions Glass and Protects Against Scratches This Somaca/CRL Counterbalanced Tilting Cutting Table is constructed of heavy gauge steel, electrically welded and painted. A full 3/4 inch smooth particle board table top and carpet is included. F.O.B : Cicero, Ill. | *$3,176.81 |
 | C.R. LAURENCE 2402503 CRL/Somaca 8 x 12 Counterbalanced Tilting Cutting Table With Breaker Bar and Air Flow 12 Outlet
Brand: C.R. Laurence Part Number: 2402503
Indoor/Outdoor Carpet: Cushions Glass and Protects Against Scratches This Somaca/CRL Counterbalanced Tilting Cutting Table is constructed of heavy gauge steel, electrically welded and painted. A full 3/4 inch smooth particle board table top and carpet is included. F.O.B : Cicero, Ill. | *$6,911.55 |
 | C.R. LAURENCE 2402504 CRL/Somaca 8 x 12 Counterbalanced Tilting Cutting Table With Breaker Bar
Brand: C.R. Laurence Part Number: 2402504
Indoor/Outdoor Carpet: Cushions Glass and Protects Against Scratches This Somaca/CRL Counterbalanced Tilting Cutting Table is constructed of heavy gauge steel, electrically welded and painted. A full 3/4 inch smooth particle board table top and carpet is included. F.O.B : Cicero, Ill. | *$5,216.29 |
 | C.R. LAURENCE 2402509 CRL/Somaca 9 x 12 Counterbalanced Tilting Cutting Table
Brand: C.R. Laurence Part Number: 2402509
Indoor/Outdoor Carpet: Cushions Glass and Protects Against Scratches This Somaca/CRL Counterbalanced Tilting Cutting Table is constructed of heavy gauge steel, electrically welded and painted. A full 3/4 inch smooth particle board table top and carpet is included. F.O.B : Cicero, Ill. | *$4,283.85 |
| C.R. LAURENCE 2402510 CRL/Somaca 8 x 10 Counterbalanced Tilting Cutting Table
Brand: C.R. Laurence Part Number: 2402510
Indoor/Outdoor Carpet: Cushions Glass and Protects Against Scratches This Somaca/CRL Counterbalanced Tilting Cutting Table is constructed of heavy gauge steel, electrically welded and painted. A full 3/4 inch smooth particle board table top and carpet is included. F.O.B : Cicero, Ill. | *$3,878.56 |
| C.R. LAURENCE 2402511 CRL/Somaca 8 x 10 Counterbalanced Tilting Cutting Table With Breaker Bar
Brand: C.R. Laurence Part Number: 2402511
Indoor/Outdoor Carpet: Cushions Glass and Protects Against Scratches This Somaca/CRL Counterbalanced Tilting Cutting Table is constructed of heavy gauge steel, electrically welded and painted. A full 3/4 inch smooth particle board table top and carpet is included. F.O.B : Cicero, Ill. | *$5,103.59 |
 | C.R. LAURENCE 2402512 CRL/Somaca 8 x 10 Counterbalanced Tilting Cutting Table With Air Flow 12 Outlet
Brand: C.R. Laurence Part Number: 2402512
Indoor/Outdoor Carpet: Cushions Glass and Protects Against Scratches This Somaca/CRL Counterbalanced Tilting Cutting Table is constructed of heavy gauge steel, electrically welded and painted. A full 3/4 inch smooth particle board table top and carpet is included. F.O.B : Cicero, Ill. | *$5,865.57 |
| C.R. LAURENCE 2402513 CRL/Somaca 8 x 10 Counterbalanced Tilting Cutting Table With Breaker Bar and Air Flow 12 Outlet
Brand: C.R. Laurence Part Number: 2402513
Indoor/Outdoor Carpet: Cushions Glass and Protects Against Scratches This Somaca/CRL Counterbalanced Tilting Cutting Table is constructed of heavy gauge steel, electrically welded and painted. A full 3/4 inch smooth particle board table top and carpet is included. F.O.B : Cicero, Ill. | *$7,123.71 |
 | C.R. LAURENCE 2402525 CRL/Somaca 9 x 12 Counterbalanced Tilting Cutting Table With Breaker Bar and Air Flow 16 Outlet
Brand: C.R. Laurence Part Number: 2402525
Indoor/Outdoor Carpet: Cushions Glass and Protects Against Scratches This Somaca/CRL Counterbalanced Tilting Cutting Table is constructed of heavy gauge steel, electrically welded and painted. A full 3/4 inch smooth particle board table top and carpet is included. F.O.B : Cicero, Ill. | *$8,426.63 |
 | C.R. LAURENCE 2402544 CRL/Somaca 9 x 12 Counterbalanced Tilting Cutting Table With Air Flow 16 Outlet
Brand: C.R. Laurence Part Number: 2402544
Indoor/Outdoor Carpet: Cushions Glass and Protects Against Scratches This Somaca/CRL Counterbalanced Tilting Cutting Table is constructed of heavy gauge steel, electrically welded and painted. A full 3/4 inch smooth particle board table top and carpet is included. F.O.B : Cicero, Ill. | *$7,021.69 |
 | C.R. LAURENCE 2402550 CRL/Somaca 8 x 10 Counterbalanced Tilting Cutting Table With Air Flow 16 Outlet
Brand: C.R. Laurence Part Number: 2402550
Indoor/Outdoor Carpet: Cushions Glass and Protects Against Scratches This Somaca/CRL Counterbalanced Tilting Cutting Table is constructed of heavy gauge steel, electrically welded and painted. A full 3/4 inch smooth particle board table top and carpet is included. F.O.B : Cicero, Ill. | *$6,845.68 |
| | C.R. LAURENCE 2402555 CRL/Somaca Break Bar (X) for 9 x 12 Hydraulic Easy Tilt Cutting Table
Brand: C.R. Laurence Part Number: 2402555
Table is Furnished With One Breaker Bar, This is an Additional Option This Break Bar is offered as and option for Cat. No. 2402522 Hydraulic Easy Tilt Table. | *$1,002.05 |
